|
| System Bus |
RS-422/485 serial |
| Bus Information |
Baud Rate, Max. |
115.2 kbps |
| Mounting Configuration |
Desktop / benchtop
Wall-mount
External module
DIN-rail mount |
| On-Board FIFO Memory Buffer |
1 sample |
| On-board Microprocessor |
Yes |
|
| Number of Channels |
1 |
| Differential Channels |
1 |
| A/D Converter Resolution |
16-bit |
| Max. A/D Speed (throughput) |
10Hz |
| Typ. A/D Speed (throughput) |
10Hz |
| Accuracy |
Relative Accuracy |
±0.05% or better |
Zero Drift |
±6µV/°C | Temperature Drift |
Span drift: ±25ppm/°C | | Noise |
CMRR (Common Mode Rejection Ratio) |
150dB (50/60Hz) |
NMRR (Normal Mode Rejection Ratio) |
100dB (50/60Hz) | | Input Impedance |
2MΩ |
| A/D Special Features |
Built-in alarm functions can be used to control a process using the built-in digital I/O lines, independent of the host PC. Microprocessor has six basic functions: - Communication software and command set
- Calibration software
- Alarm monitoring
- Event counting
- Management of the EEPROM device that holds the system parameters
- Data transformation
|
|
| Bipolar Input Ranges |
-10V to +10V
-5V to +5V
-1V to +1V
-500mV to +500mV
-150mV to +150mV |
| Current Input Ranges |
-20 to +20mA |
| A/D Range Selection |
Software |
| Input Range Details |
Current input requires a 125-ohm resistor. Depending on the module’s configuration setting, it can forward the data to the host computer in one of the following formats: - engineering units (mV, V, or mA)
- percent of full-scale range (FSR)
- twos complement hexadecimal
|
| Gains |
1
2
10
20
66.7 |
| Gain Range Details |
Gains apply to base range of ±10V |
| Isolation, Field-to-Logic |
3000VDC |
|
| Triggering Type(s) Supported |
Software trigger (software-controlled trigger)
Counter/timer trigger (triggered by on-board counter/timer) |
|
| Number of User Channels |
1 |
| Counter/Timer Size |
16-bit |
| Input Frequency, max. |
50Hz |
| Counter Type(s) |
Up counter |
| Counter Range |
0ft
....40.72mi
(0mm....65.54km)
|
| Clock Source(s) |
None; input tied to the module's analog input channel. |
| Signals |
Input Voltage - High (Vih) |
3.5V....30V |
Input Voltage - Low (Vil) |
0mV....1V | | Pulse Width, High, min. |
1ms |
| Pulse Width, Low, min. |
1ms |
|
| Number of I/O Lines |
3 |
| Primary Digital I/O |
Configuration |
1 input
2 outputs |
Input/Output Selection |
Fixed | Inputs |
Input Voltage - High (Vih, DC) |
3.5V....30V | Input Voltage - Low (Vil) |
0mV....1V | Digital Input Features |
Input channel is tied to the event counter input. Pull Up Current: 0.5mA; 10Kohm resistor to +5V | Outputs |
Output Current Sink, max. |
30mA | Output Current Sink Details |
Open collector to 30V, 30mA max. load; power dissipation: 300mW | Output/Relay Details |
When activated, the on-board alarm function is tied to the two digital outputs: Digital output 0 is tied to the Low alarm state, turning ON if the Low alarm limit is reached (can be momentary, until the A/D input returns within allowed range, or latching where it stays on continuously until the Clear Alarm command is received or the High alarm limit is reached. Digital output 1 is tied to the High alarm state, turning ON if the High alarm limit is reached (can be momentary, until the A/D input returns within allowed range, or latching where it stays on continuously until the Clear Alarm command is received or the Low alarm limit is reached. This arrangement of coupling High and Low alarm states with the digital output lines may be utilized to build ON/OFF controllers that can operate without host computer involvement. | |
| Operating System Compatibility |
Windows NT
Windows 2000
Windows 98
Windows 95 |
| Software Compatibility |
Labtech NOTEBOOK®
DASYLab®
GENIDaq
Labtech CONTROL®
Labtech NOTEBOOKpro®
Labtech CONTROLpro®
DASYLab Lite®
LabVIEW® |
|
| Connector #1 |
Quantity |
10 |
Type |
Screw terminals as removable (lift-off) terminal strips | Location |
On module | | Connector & Cabling Details |
4 terminals for RS-422/485 data, DC supply voltage, and ground.
One terminal can reset module to default address/baud rate.
Other terminals for voltage/current input. |
|
| Construction Material |
Impact resistant ABS plastic |
|
| Power Consumption (typical) |
Unregulated +10 to +30VDC, 1.2W |
| Power Supply Notes |
Power Requirements: Unregulated +10 to +30VDC |
|
| Watchdog Timer Included |
Yes |
| Watchdog Timer Intervals |
100ms to 100 seconds in 0.1-second intervals |
|
| Operating Temperature |
32°F....158°F
(0°C....70°C)
|
| Relative Humidity, noncondensing |
0%....95% |
|
| Width |
2.76"
(70mm)
|
| Height |
1.65"
(42mm)
|
| Depth |
4.38"
(111.3mm)
|
| Dimension Details |
Height: 1" (25mm) without removable DIN-rail mounting bracket. Wall-mount bracket (included) adds 6.2mm (31.2mm height w/steel wall-mount bracket). |