CyberResearch Home 1-800-341-2525 HomeProductsLive HelpPrintClose Window
Home  Engineering Software & Communications  Modular / Remote Data Acquisition  CYMOD & ADAM Modules
Data Acquisition Module with 8 Channels A/D and 3 DIO
Data Acquisition Module with 8 Channels A/D and 3 DIO
ADAM 4017

ADAM Remote Data Acquisition Module - 8 Channels of 16-bit A/D (6 Diff/2 S.E.), 3 DIO
Qty   Price (with options selected)
Shipping: Low Stock
 Features
System BusRS-422/485 serial
Number of Channels8
A/D Converter Resolution16-bit
Max. A/D Speed (throughput)10Hz
Data Acquisition Module with 8 Channels A/D and 3 DIO Data Acquisition Module with 8 Channels A/D and 3 DIO You Can Easily Panel-Mount, DIN Rail-Mount, or Piggyback-Mount Modules Modules Communicate Over a Single Twisted Pair
 
Introduction

There are three ADAM™ modules intended for general analog inputs. All three support both voltage and current inputs, and all provide 3000VDC isolation.

  • ADAM 4012 has one differential input with 2 megohms impedance.
  • ADAM 4017 has six differential and two single-ended inputs with 20 megohms impedance.
  • ADAM 4017P adds Modbus compliance to ADAM 4017.

ADAM modules use a single twisted pair of wires to transmit and receive data. All module commands are issued in printable ASCII characters. You can easily panel-mount, DIN-rail-mount, or piggyback-mount modules. Removable screw terminal connectors make wiring and field maintenance easy.

Modules accept any unregulated power source between 10 and 30 VDC. A watchdog timer supervisory function automatically resets the modules in the event of system failure.

Our CyMOD series of modules has been designed with state-of-the art surface-mount technology to be completely hardware and software compatible with the ADAM series, at a somewhat lower cost. CM 4011, CM 4011D, and CM 4018 are thermocouple modules that parallel the similarly numbered ADAM modules.
  Less Detail  More Detail
Product Information
System Bus RS-422/485 serial
Bus Information Baud Rate, Max. 115.2 kbps
System Bus Details ADAM 4017P accepts Modbus input
Mounting Configuration Desktop / benchtop
Wall-mount
External module
DIN-rail mount
On-Board FIFO Memory Buffer 1 sample per channel
On-board Microprocessor Yes
Analog Input Channels
Number of Channels 8
Single-Ended Channels 2
Differential Channels 6
A/D Converter Resolution 16-bit
Max. A/D Speed (throughput) 10Hz
Typ. A/D Speed (throughput) 10Hz
A/D Converter Settling Time 100ms
Bandwidth 15.72Hz
A/D Speed/Bandwidth Details Bandwidth: 13.1Hz @ 50Hz; 15.72Hz @ 60Hz
Accuracy Relative Accuracy ±0.1% or better
Zero Drift ±6µV/°C
Temperature Drift Span drift: ±25ppm/°C
Noise CMRR (Common Mode Rejection Ratio) 92dB (50/60Hz)
Input Impedance 20MΩ
Input Impedance Details Input impedance is 20 megohms for voltage inputs, 120 ohms for current inputs.
A/D Special Features

Microprocessor has six basic functions:

  • Communication software and command set
  • Calibration software
  • Alarm monitoring
  • Event counting
  • Management of the EEPROM device that holds the system parameters
  • Data transformation
Input Ranges
Bipolar Input Ranges -10V to +10V
-5V to +5V
-1V to +1V
-500mV to +500mV
-150mV to +150mV
Current Input Ranges -20 to +20mA
A/D Range Selection Software
Input Range Details

Current input requires a 125-ohm resistor.

Depending on the module’s configuration setting, it can forward the data to the host computer in one of the following formats:

  • engineering units (mV, V, or mA)
  • percent of full-scale range (FSR)
  • twos complement hexadecimal
Gains 1
2
10
20
66.7
Gain Range Details Gains apply to base range of ±10V
Isolation, Field-to-Logic 3000VDC
Trigger Modes
Triggering Type(s) Supported Software trigger (software-controlled trigger)
Software
Software Included - Features Setup and utility software included
Operating System Compatibility Windows NT
Windows 2000
Windows 98
Windows 95
Software Compatibility Labtech NOTEBOOK®
DASYLab®
GENIDaq
Labtech CONTROL®
Labtech NOTEBOOKpro®
Labtech CONTROLpro®
DASYLab Lite®
LabVIEW®
Cables and Connectors
Connector #1 Quantity 20
Type Screw terminals as removable (lift-off) terminal strips
Location On module
Connector #2 Location On module
Connector & Cabling Details 4 terminals for RS-422/485 data, DC supply voltage, and ground.
One terminal can reset module to default address/baud rate.
Other 15 terminals are used for voltage input channels and analog ground.
Construction
Construction Material Impact resistant ABS plastic
Power
Power Consumption (typical) Unregulated +10 to +30VDC, 1.2W
Power Supply Notes Power Requirements: Unregulated +10 to +30VDC
System Monitoring
Watchdog Timer Included Yes
Watchdog Timer Intervals 100ms to 100 seconds in 0.1-second intervals
Environmental Specifications
Operating Temperature 32°F....158°F (0°C....70°C)
Relative Humidity, noncondensing 0%....95%
Dimensions
Width 2.76" (70mm)
Height 1.65" (42mm)
Depth 4.83" (122.6mm)
Dimension Details Height: 1" (25mm) without removable DIN-rail mounting bracket. Wall-mount bracket (included) adds 6.2mm (31.2mm height w/steel wall-mount bracket).
Less Detail Less Detail
 
Ordering - Includes Options Indicated Below
ADAM 4017
ADAM Remote Data Acquisition Module - 8 Channels of 16-bit A/D (6 Diff/2 S.E.), 3 DIO		 $200.00
ADAM 4017P
ADAM Remote Data Acquisition Module - 8 Channels of 16-bit A/D (6 Diff/2 S.E.), 3 DIO, Modbus Compliant		 $270.00

Driver Software Options
None  
PCL LV
LabVIEW® Controls for Win95/98/NT		 $0.00
PCL OCX
ActiveX® Controls for Win95/98/NT		 $0.00
ADAM OPC
ADAM OPC Server Software for Win95/98/NT		 $225.00

Serial Converters and Repeaters
None  
ADAM 4510S
ADAM Isolated RS-422/485 Repeater Module, 115.2 kpbs Data Rate, with Screw Terminals & 3000VDC Isolation		 $155.00
ADAM 4520
ADAM Remote RS-232 to RS-422/485 Converter Module, 115.2 kpbs Data Rate, with Screw Terminals and 3000VDC Isolation		 $95.00
CM 4510
CyMOD RS-422/485 Repeater Module		 $120.00
CM 4520
CyMOD RS-232 to RS-422/485 Converter Module, 5000 Vrms Isolation		 $90.00
CM 4530
CyMOD USB to RS-232/422/485 Converter Module, 2500 Vrms Isolation, with 10-Pin Screw Terminal Block and LED Indicator		 $125.00

Power Supply Options
None  
CM 243
24VDC Power Supply, 72W, Provides 3A @ 24V from 110/220VAC		 $100.00
Catalog # Shipping Price (with options) Qty  
ADAM 4017 Low Stock
Customers Were Also Interested In These
Did you find this page useful?
Toll-Free Hotline 1-800-341-2525 • Tel: 203-483-8815 • Fax: 203-483-9024
©Copyright 2009 , CyberResearch Inc., Branford, CT USA All Rights Reserved