|
| System Bus |
USB 2.0 |
| Bus Information |
Baud Rate, Max. |
24 bps |
Bus Standards Compliance |
USB 1.1
USB 2.0 | System Bus Details |
USB Type B (4-pin, square) female connector | | Mounting Configuration |
Desktop / benchtop
External module |
| Direct Sensor Input |
Thermocouple
RTD
Thermistor |
| On-board Microprocessor |
Yes |
| On-Board Memory for Processor |
1.5k |
|
| Number of Channels |
8 |
| Differential Channels |
8 |
| A/D Converter Resolution |
24-bit |
| Max. A/D Speed (throughput) |
24Hz |
| Cold Junction Compensation |
CJC on all channels |
| Accuracy |
Relative Accuracy |
- Max. error from thermocouple inputs: +/-2.653 deg. C.
- Max. error from TMP36 or equiv. semiconductors: +/-0.5 deg. C.
- Max. error from thermistor inputs: +/-0.05 deg. C.
Resistance values greater than 660 ohms cannot be measured by this module in the RTD mode. Maximum and typical accuracy errors for RTD mode vary with temperature, as follows:
- -200 to -150 deg C: +/-2.85 deg. C max., +/-2.59 deg. C typ.
- -150 to -100 deg C: +/-1.24 deg. C max., +/-0.97 deg. C typ.
- -100 to 0 deg C: +/-0.58 deg. C max., +/-0.31 deg. C typ.
- 0 to 1000 deg C: +/-0.38 deg. C max., +/-0.11 deg. C typ.
- 100 to 300 deg C: +/-0.39 deg. C max., +/-0.12 deg. C typ.
- 300 to 600 deg C: +/-0.40 deg. C max., +/-0.12 deg. C typ.
|
| Noise |
CMRR (Common Mode Rejection Ratio) |
100 dB min. |
NMRR (Normal Mode Rejection Ratio) |
90 dB min. | | Input Impedance |
5000MΩ |
| Input Impedance Details |
5 Gigohm, min. |
| Input Protection |
Protected against voltages to +/-25VDC, max. (power on), +/-40VDC (power off) |
| A/D Special Features |
Max. Logging Rate/Channel: 2 S/s to PC, 1 S/s to CF card |
|
| Bipolar Input Ranges |
-80mV to +80mV |
| Unipolar Input Ranges |
0 to +2.5V
0 to +2V
0 to +500mV |
| Thermocouple Support |
Thermocouple Inputs |
J-type thermocouple
K-type thermocouple
T-type thermocouple
E-type thermocouple
R-type thermocouple
S-type thermocouple
B-type thermocouple
N-type thermocouple |
J-type Range Supported |
-346°F....2192°F
(-210°C....1200°C)
| K-type Range Supported |
-454°F....2501.6°F
(-270°C....1372°C)
| T-type Range Supported |
-454°F....752°F
(-270°C....400°C)
| E-type Range Supported |
-454°F....1832°F
(-270°C....1000°C)
| R-type Range Supported |
-58°F....3214.4°F
(-50°C....1768°C)
| S-type Range Supported |
-58°F....3214.4°F
(-50°C....1768°C)
| B-type Range Supported |
32°F....3308°F
(0°C....1820°C)
| | RTD Types Supported |
100-ohm Platinum (-100° to +100°C), alpha = 0.00385 (IEC)
100-ohm Platinum (0° to +200°C), alpha = 0.00385 (IEC)
100-ohm Platinum (0° to +600°C), alpha = 0.00385 (IEC)
100-ohm Platinum (0° to +850°C), alpha = 0.00385 (IEC)
100-ohm Platinum
100-ohm Platinum (-100° to +200°C), alpha = 0.00385 (IEC)
100-ohm Platinum (-100° to +100°C), alpha = 0.003916 (JIS)
100-ohm Platinum (-100° to +200°C), alpha = 0.003916 (JIS)
100-ohm Platinum (0° to +100°C), alpha = 0.003916 (JIS)
100-ohm Platinum (0° to +600°C), alpha = 0.003916 (JIS)
100-ohm Platinum (0° to +850°C), alpha = 0.003916 (JIS)
100-ohm Platinum (-50° to +150°C), alpha = 0.00385 (IEC)
100-ohm Platinum (-50° to +150°C), alpha = 0.003916 (JIS)
100-ohm Platinum (-200° to +200°C), alpha = 0.00385 (IEC)
100-ohm Platinum (0° to +400°C), alpha = 0.00385 (IEC)
100-ohm Platinum (-200° to +200°C), alpha = 0.003916 (JIS)
100-ohm Platinum (0° to +400°C), alpha = 0.003916 (JIS)
100-ohm Platinum (-200° to +600°C), alpha = 0.00385 (IEC)
100-ohm Platinum (-200° to +600°C), alpha = 0.003916 (JIS) |
| Thermistor Support |
Thermistor Range |
Thermistor:
- Standard 2,252 ohm through 30,000 0hm
- Resistance values greater than 180 kohms can not be measured when in thermister mode
- For accurate three-wire compensation, each individual lead wire resistance connected to the +/- Ix pins must be of equal value
|
| A/D Range Selection |
Software |
| Input Range Details |
Range is automatically selected by configuring sensor type in software. |
| Isolation, Field-to-Logic |
500VDC |
| Isolation Details |
Isolation of 500VDC min., between field wiring and USB interface. |
|
| Triggering Type(s) Supported |
Software trigger (software-controlled trigger) |
| Triggering Features |
Min. 1 sec between entries, max. 2exp32 sec., intervals of 1 sec. |
|
| Number of I/O Lines |
8 |
| Primary Digital I/O |
Configuration |
8 bidirectional |
Input/Output Selection |
Software | Signal Connector |
Screw terminals. | Inputs |
Input Voltage - High (Vih, DC) |
2V....5.5V | Input Voltage - Low (Vil) |
-5V....0.8V | Outputs |
Output Voltage - High (Voh) |
3.5V....5V | Output Voltage - Low (Vol) |
0mV....0.7V | Output Current Sink, max. |
2.5mA | |
| Software Included Free with Product |
Software developer's kit
calibration software |
| Software Included - Features |
Drivers and libraries |
| Operating System Compatibility |
Windows XP
Windows 2000
Windows Me
Windows 98SE |
| Software Compatibility |
Universal Driver Library
DASYLab®
LabVIEW® |
|
| Connector #1 |
Quantity |
52 |
Type |
Screw terminals | Location |
On module | | Connector #2 |
Quantity |
1 |
Type |
USB Type B (4-pin, square) | Gender |
Female (socket) | Location |
On module | |
| Construction Material |
Impact resistant ABS plastic |
|
| Power Consumption (typical) |
500mA max. from USB line. Data logging requires use of included AC adapter power supply. |
| Power Supply Notes |
Includes external 5V power supply:
- Output voltage: 5V
- Output power: 2.5W
- Input voltage: 100~240VAC @ 50~60Hz
- Input current: 0.2A
|
|
| Other Control Features |
Push button on side to initiate data logging |
| Display |
LED show status of signal |
|
| Operating Temperature |
32°F....158°F
(0°C....70°C)
|
| Storage Temperature |
-40°F....185°F
(-40°C....85°C)
|
| Relative Humidity, noncondensing |
0%....90% |
|
| Width |
3.45"
(87.7mm)
|
| Height |
1.5"
(38.17mm)
|
| Depth |
5.1"
(129.52mm)
|
|
| Weight |
0.42lbs
(190.51g
)
|
| Shipping Weight |
1.8lbs
(816.46g
)
|